長沙衛生間隔斷施工方案1、安裝固定板在墻壁上找到合適的位置畫出固定片的中心線，看固定板上有幾個固定用的螺絲孔，然后在墻壁中心線上對應的打上幾個孔，把塑膠賽套放入孔內，接下來就是用膨脹絲把固定板固定...

長沙公共衛生間隔斷施工方案

1、安裝固定板

在墻壁上找到合適的位置畫出固定片的中心線，看固定板上有幾個固定用的螺絲孔，然后在墻壁中心線上對應的打上幾個孔，把塑膠賽套放入孔內，接下來就是用膨脹絲把固定板固定在墻上。

2、安裝調整底座

根據預先設計好的施工圖，在衛生間地板上地板找到底座位置并畫出中心線，然后固定底座（底座位置距隔斷板邊緣大約20厘米左右）

3、安裝隔間板

前兩步的工作就是為安裝隔間板打鋪墊的，固定板和底座的作用就是用來固定隔間板的，把隔間板放在調整底座上，然后調整底座高低使隔間板緊貼墻壁上的固定板，然后再微調底座高低使隔間板距地面有一定距離，大約15厘米就好，然后用水平尺確定水平，等一切都調整好后，用螺絲把隔間板固定在固定板和調整底座上。

4、安裝拉桿

依隔間實際長度裁切固定，直線拉桿平接時，管內須加裝圓形相接套及緊迫連接彈簧片以確定接頭平整、堅固，其相接處應在上繃固定片內，以增加美觀。對于隔間90度轉角拉桿，采用鋁合金射出成型之90度轉角接頭，連接轉角兩端之拉桿。以凸圓形墻壁固定套，用螺絲將終端拉桿固定在墻面上。使用螺絲將拉桿于立柱上緣固定片連接固定一起。

5、安裝立柱

用螺絲將拉桿固定片，固定于立柱中間頂端，以L型固定片片，將立柱與隔間板固定結合一體墻邊立柱－－在墻面上畫出與地面垂直之直線，以電鉆在線上3外鉆孔，預埋塑膠塞套于孔內，確定與地垂直后，用螺絲以L型固定片，將墻邊立柱固定在離地145高處墻壁上。終端立柱－－固定上緣拉桿固定片及L型邊接片于終端立柱上，再以螺絲將此板固定于隔間板上

6、安裝門扇

把鉸鏈座或頁鼻固定在立柱上，估量兩三個就行，然后再門扇上的對應位置安裝對應數量的鉸鏈片，輕抬門扇，把自動歸位尼龍座放置鉸鏈座內，調整位置，并開關門檢查一下看門扇時候能開關自如，檢查調整，直到滿意為止。